Перевод: с французского на все языки

со всех языков на французский

nominal voltage

  • 1 tension assignée

    1. номинальное напряжение

     

    номинальное напряжение
    Напряжение, установленное изготовителем для прибора
    [ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]

    номинальное напряжение Uном, кВ
    Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
    [ ГОСТ Р 52726-2007]

    номинальное напряжение

    Un
    Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
    [ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]

    EN

    rated voltage
    voltage assigned to the appliance by the manufacturer
    [IEC 60335-1, ed. 4.0 (2001-05)]

    rated voltage
    quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    rated voltage
    input or output supply voltage for which equipment is designed or specified
    [IEC 88528-11, ed. 1.0 (2004-03)]

    rated voltage
    specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
    NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    rated voltage
    the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
    NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    rated voltage
    reference voltage for which the cable is designed, and which serves to define the electrical tests
    NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
    Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
    U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
    In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
    This condition applies both to the value Uo and to the value U.
    In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
    NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
    [IEC 60245-1, ed. 4.0 (2003-12)]

    rated voltage
    highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
    [IEC 60800, ed. 3.0 (2009-07)]

    rated voltage
    the r.m.s. line-to-line voltage under rated conditions
    Primary side of input transformer: ULN
    Converter input: UVN
    Converter output: UaN
    Motor voltage: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    rated voltage
    input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
    [IEC 62040-1, ed. 1.0 (2008-06)]

    nominal voltage, Un
    voltage by which a system is designated or identified
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    FR

    tension assignée
    tension attribuée à l'appareil par le fabricant
    [IEC 60335-1, ed. 4.0 (2001-05)]

    tension nominale
    tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    tension assignée
    tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
    NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    tension assignée
    valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
    NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    tension assignée
    tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
    NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
    Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
    U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
    Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
    Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
    Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
    NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
    [IEC 60245-1, ed. 4.0 (2003-12)]

    tension assignée
    tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
    [IEC 60800, ed. 3.0 (2009-07)]

    tension assignée
    valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
    Primaire du transformateur d’entrée: ULN
    Entrée du convertisseur: UVN
    Sortie du convertisseur: UaN
    Moteur: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    tension assignée
    tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
    [IEC 62040-1, ed. 1.0 (2008-06)]

    tension nominale, Un
    tension par laquelle un réseau est désigné ou identifié
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    Тематики

    Синонимы

    • Un

    EN

    FR

    Франко-русский словарь нормативно-технической терминологии > tension assignée

  • 2 tension nominale

    1. номинальное напряжение конденсатора
    2. номинальное напряжение

     

    номинальное напряжение
    Напряжение, установленное изготовителем для прибора
    [ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]

    номинальное напряжение Uном, кВ
    Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
    [ ГОСТ Р 52726-2007]

    номинальное напряжение

    Un
    Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
    [ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]

    EN

    rated voltage
    voltage assigned to the appliance by the manufacturer
    [IEC 60335-1, ed. 4.0 (2001-05)]

    rated voltage
    quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    rated voltage
    input or output supply voltage for which equipment is designed or specified
    [IEC 88528-11, ed. 1.0 (2004-03)]

    rated voltage
    specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
    NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    rated voltage
    the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
    NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    rated voltage
    reference voltage for which the cable is designed, and which serves to define the electrical tests
    NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
    Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
    U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
    In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
    This condition applies both to the value Uo and to the value U.
    In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
    NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
    [IEC 60245-1, ed. 4.0 (2003-12)]

    rated voltage
    highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
    [IEC 60800, ed. 3.0 (2009-07)]

    rated voltage
    the r.m.s. line-to-line voltage under rated conditions
    Primary side of input transformer: ULN
    Converter input: UVN
    Converter output: UaN
    Motor voltage: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    rated voltage
    input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
    [IEC 62040-1, ed. 1.0 (2008-06)]

    nominal voltage, Un
    voltage by which a system is designated or identified
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    FR

    tension assignée
    tension attribuée à l'appareil par le fabricant
    [IEC 60335-1, ed. 4.0 (2001-05)]

    tension nominale
    tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    tension assignée
    tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
    NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    tension assignée
    valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
    NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    tension assignée
    tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
    NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
    Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
    U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
    Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
    Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
    Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
    NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
    [IEC 60245-1, ed. 4.0 (2003-12)]

    tension assignée
    tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
    [IEC 60800, ed. 3.0 (2009-07)]

    tension assignée
    valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
    Primaire du transformateur d’entrée: ULN
    Entrée du convertisseur: UVN
    Sortie du convertisseur: UaN
    Moteur: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    tension assignée
    tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
    [IEC 62040-1, ed. 1.0 (2008-06)]

    tension nominale, Un
    tension par laquelle un réseau est désigné ou identifié
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    Тематики

    Синонимы

    • Un

    EN

    FR

     

    номинальное напряжение конденсатора
    Максимальное напряжение, при котором конденсатор может работать в течение минимальной наработки в условиях, указанных в нормативно-технической документации
    [ ГОСТ 21415-75]

    номинальное напряжение конденсатора
    Действующее значение синусоидального переменного напряжения при номинальной частоте, на которое рассчитан конденсатор. Номинальное напряжение многофазного конденсатора - значение напряжения между выводами.
    [ ГОСТ 1282-88]

    Тематики

    EN

    DE

    FR

    Франко-русский словарь нормативно-технической терминологии > tension nominale

  • 3 Un

    1. номинальное напряжение

     

    номинальное напряжение
    Напряжение, установленное изготовителем для прибора
    [ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]

    номинальное напряжение Uном, кВ
    Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
    [ ГОСТ Р 52726-2007]

    номинальное напряжение

    Un
    Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
    [ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]

    EN

    rated voltage
    voltage assigned to the appliance by the manufacturer
    [IEC 60335-1, ed. 4.0 (2001-05)]

    rated voltage
    quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    rated voltage
    input or output supply voltage for which equipment is designed or specified
    [IEC 88528-11, ed. 1.0 (2004-03)]

    rated voltage
    specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
    NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    rated voltage
    the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
    NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    rated voltage
    reference voltage for which the cable is designed, and which serves to define the electrical tests
    NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
    Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
    U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
    In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
    This condition applies both to the value Uo and to the value U.
    In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
    NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
    [IEC 60245-1, ed. 4.0 (2003-12)]

    rated voltage
    highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
    [IEC 60800, ed. 3.0 (2009-07)]

    rated voltage
    the r.m.s. line-to-line voltage under rated conditions
    Primary side of input transformer: ULN
    Converter input: UVN
    Converter output: UaN
    Motor voltage: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    rated voltage
    input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
    [IEC 62040-1, ed. 1.0 (2008-06)]

    nominal voltage, Un
    voltage by which a system is designated or identified
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    FR

    tension assignée
    tension attribuée à l'appareil par le fabricant
    [IEC 60335-1, ed. 4.0 (2001-05)]

    tension nominale
    tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
    [IEC 60034-18-41, ed. 1.0 (2006-10)]

    tension assignée
    tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
    NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
    [IEC 60349-1, ed. 1.0 (1999-11)]

    tension assignée
    valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
    NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
    [IEC 62497-1, ed. 1.0 (2010-02)]

    tension assignée
    tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
    NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
    Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
    U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
    Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
    Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
    Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
    NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
    [IEC 60245-1, ed. 4.0 (2003-12)]

    tension assignée
    tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
    [IEC 60800, ed. 3.0 (2009-07)]

    tension assignée
    valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
    Primaire du transformateur d’entrée: ULN
    Entrée du convertisseur: UVN
    Sortie du convertisseur: UaN
    Moteur: UAN
    [IEC 61800-4, ed. 1.0 (2002-09)]

    tension assignée
    tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
    [IEC 62040-1, ed. 1.0 (2008-06)]

    tension nominale, Un
    tension par laquelle un réseau est désigné ou identifié
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    Тематики

    Синонимы

    • Un

    EN

    FR

    Франко-русский словарь нормативно-технической терминологии > Un

  • 4 tension d’alimentation déclarée

    1. напряжение в системе электроснабжения

     

    напряжение в системе электроснабжения
    Uc
    Напряжение Uc, в качестве которого обычно принимают номинальное напряжение Unom в системе электроснабжения. Если по согласованию между поставщиком и потребителем электрической энергии напряжение электрической сети отличается от номинального напряжения, то данное напряжение принимают в качестве напряжения в системе электроснабжения Uc.
    [ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]

    EN

    declared supply voltage
    Uc

    declared supply voltage Uc is normally the nominal voltage Un of the system. If, by agreement between the supplier and the customer, a voltage different from the nominal voltage is applied to the terminal, then this voltage is the declared supply voltage Uc
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    FR

    tension d’alimentation déclarée
    Uc

    la tension d’alimentation déclarée Uc est généralement la tension nominale Un du réseau. Si, par suite d’un accord entre le l’opérateur de réseau et le client, la tension d’alimentation appliquée à ses bornes diffère de la tension nominale, alors, cette tension correspond à la tension d’alimentation déclarée Uc
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    Тематики

    Синонимы

    • Uc

    EN

    FR

    • tension d’alimentation déclarée
    • Uc

    Франко-русский словарь нормативно-технической терминологии > tension d’alimentation déclarée

  • 5 Uc

    1. напряжение в системе электроснабжения

     

    напряжение в системе электроснабжения
    Uc
    Напряжение Uc, в качестве которого обычно принимают номинальное напряжение Unom в системе электроснабжения. Если по согласованию между поставщиком и потребителем электрической энергии напряжение электрической сети отличается от номинального напряжения, то данное напряжение принимают в качестве напряжения в системе электроснабжения Uc.
    [ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]

    EN

    declared supply voltage
    Uc

    declared supply voltage Uc is normally the nominal voltage Un of the system. If, by agreement between the supplier and the customer, a voltage different from the nominal voltage is applied to the terminal, then this voltage is the declared supply voltage Uc
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    FR

    tension d’alimentation déclarée
    Uc

    la tension d’alimentation déclarée Uc est généralement la tension nominale Un du réseau. Si, par suite d’un accord entre le l’opérateur de réseau et le client, la tension d’alimentation appliquée à ses bornes diffère de la tension nominale, alors, cette tension correspond à la tension d’alimentation déclarée Uc
    [IEC 61000-4-30, ed. 2.0 (2008-10)]

    Тематики

    Синонимы

    • Uc

    EN

    FR

    • tension d’alimentation déclarée
    • Uc

    Франко-русский словарь нормативно-технической терминологии > Uc

  • 6 tension d'emploi assignée

    1. номинальное рабочее напряжение

     

    Номинальное рабочее напряжение
    Ue

    Номинальное рабочее напряжение (далее — номинальное напряжение) выключателя — устанавливаемое изготовителем значение напряжения, связанное с его работоспособностью (особенно при коротких замыканиях).
    Примечание — Для одного выключателя можно установить несколько значений номинального напряжения с соответствующими значениями номинальной наибольшей отключающей способности
    [ ГОСТ Р 50345-99( МЭК 60898-95)]


    номинальное напряжение автоматического выключателя
    Номинальным напряжением автоматического выключателя называют значение напряжения, которое способны выдержать главные токоведущие части выключателя в длительном режиме.
    [А.В.Беляев. Выбор аппаратуры, защит и кабелей в сетях 0,4 кВ. - Л.: Энергоатомиздат. 1988]

    номинальное рабочее напряжение
    -
    [IEV number 442-01-07]

    EN

    rated operating voltage
    nominal voltage of the supply(ies) for which the pole of the accessory is intended to be used
    [IEC 62196-1, ed. 1.0 (2003-04)]


    rated operating voltage
    the nominal voltage of the supply for which the accessory is intended to be used
    [IEC 60309-1, ed. 4.0 (1999-02)]
    [IEV number 442-01-07]

    FR

    tension d'emploi assignée
    tension nominale de l'alimentation ou des alimentations pour laquelle la borne de l'appareil est prévue
    [IEC 62196-1, ed. 1.0 (2003-04)]


    tension nominale d'emploi
    tension nominale du réseau pour lequel l'appareil est destiné à être utilisé
    [IEC 60309-1, ed. 4.0 (1999-02)]
    [IEV number 442-01-07]

    Тематики

    Близкие понятия

    Синонимы

    EN

    FR

    Франко-русский словарь нормативно-технической терминологии > tension d'emploi assignée

  • 7 tension nominale d'emploi

    1. номинальное рабочее напряжение

     

    Номинальное рабочее напряжение
    Ue

    Номинальное рабочее напряжение (далее — номинальное напряжение) выключателя — устанавливаемое изготовителем значение напряжения, связанное с его работоспособностью (особенно при коротких замыканиях).
    Примечание — Для одного выключателя можно установить несколько значений номинального напряжения с соответствующими значениями номинальной наибольшей отключающей способности
    [ ГОСТ Р 50345-99( МЭК 60898-95)]


    номинальное напряжение автоматического выключателя
    Номинальным напряжением автоматического выключателя называют значение напряжения, которое способны выдержать главные токоведущие части выключателя в длительном режиме.
    [А.В.Беляев. Выбор аппаратуры, защит и кабелей в сетях 0,4 кВ. - Л.: Энергоатомиздат. 1988]

    номинальное рабочее напряжение
    -
    [IEV number 442-01-07]

    EN

    rated operating voltage
    nominal voltage of the supply(ies) for which the pole of the accessory is intended to be used
    [IEC 62196-1, ed. 1.0 (2003-04)]


    rated operating voltage
    the nominal voltage of the supply for which the accessory is intended to be used
    [IEC 60309-1, ed. 4.0 (1999-02)]
    [IEV number 442-01-07]

    FR

    tension d'emploi assignée
    tension nominale de l'alimentation ou des alimentations pour laquelle la borne de l'appareil est prévue
    [IEC 62196-1, ed. 1.0 (2003-04)]


    tension nominale d'emploi
    tension nominale du réseau pour lequel l'appareil est destiné à être utilisé
    [IEC 60309-1, ed. 4.0 (1999-02)]
    [IEV number 442-01-07]

    Тематики

    Близкие понятия

    Синонимы

    EN

    FR

    Франко-русский словарь нормативно-технической терминологии > tension nominale d'emploi

  • 8 tension nominale (d'une installation électrique), f

    1. номинальное напряжение (электрической установки)

     

    номинальное напряжение (электрической установки)
    Значение напряжения, которым электрическая установка или ее часть обозначена и по которому она идентифицируется.
    [ ГОСТ Р МЭК 60050-826-2009]

    Переходные напряжения, вызванные, например, коммутационными оперированиями, и временные колебания напряжения из-за анормальных условий, таких как повреждения в системе питания, не учитываются
    [ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]

    EN

    nominal voltage (of an electrical installation)
    value of the voltage by which the electrical installation or part of the electrical installation is designated and identified
    [IEV number 826-11-01]

    FR

    tension nominale (d'une installation électrique), f
    valeur de la tension par laquelle l’installation électrique ou une partie de l’installation électrique est désignée et identifiée
    [IEV number 826-11-01]

    Тематики

    EN

    DE

    • Nennspannung (einer elektrischen Anlage), f

    FR

    • tension nominale (d'une installation électrique), f

    Франко-русский словарь нормативно-технической терминологии > tension nominale (d'une installation électrique), f

  • 9 tension nominale du système de distribution

    1. номинальное напряжение распределительной сети

     

    номинальное напряжение распределительной сети
    Un
    Напряжение, указанное в обозначении распределительной сети или аппаратуры, к которому относятся установленные рабочие характеристики
    [МЭК 38, пункт 1, измененный]
    [ ГОСТ Р 61557-1-2006]

    EN

    nominal voltage of the distribution system (Un)
    voltage by which a distribution system or equipment is designated and to which certain operating characteristics are referred
    [IEC 61557-1, definition 3.1]

    FR

    tension nominale du système de distribution (Un)
    tension pour laquelle un système de distribution est conçu et à laquelle certaines caractéristiques de fonctionnement font référence
    [IEC 61557-1, definition 3.1]

    Тематики

    EN

    FR

    Франко-русский словарь нормативно-технической терминологии > tension nominale du système de distribution

  • 10 tension nominale, f

    1. номинальное напряжение химического источника тока

     

    номинальное напряжение химического источника тока
    номинальное напряжение

    Условное напряжение, определяемое электрохимической системой химического источника тока.
    [ ГОСТ 15596-82]

    EN

    nominal voltage
    suitable approximate value of the voltage used to designate or identify a cell, a battery or an electrochemical system
    [IEV number 482-03-31]

    FR

    tension nominale, f
    valeur approchée appropriée d’une tension, utilisée pour désigner ou identifier un élément, une batterie, ou un système électrochimique
    [IEV number 482-03-31]

    Тематики

    Классификация

    >>>

    Синонимы

    EN

    DE

    FR

    • tension nominale, f

    Франко-русский словарь нормативно-технической терминологии > tension nominale, f

  • 11 ecart de tension

    1. отклонение напряжения

     

    отклонение напряжения
    Величина, равная разности между значением напряжения в данной точке системы электроснабжения в рассматриваемый момент времени и его номинальным или базовым значением.
    [ ГОСТ 23875-88]

    EN

    voltage deviation
    the difference, generally expressed as a percentage, between the voltage at a given instant at a point in the system, and a reference voltage such as: nominal voltage, a mean value of the operating voltage, declared supply voltage
    [IEV number 604-01-17]

    FR

    écart de tension
    différence, exprimée généralement en pourcentage, en un point du réseau et à un instant donné, entre la tension effective en ce point et une tension de référence telle que la tension nominale, la tension moyenne d'exploitation ou la tension contractuelle de fourniture
    [IEV number 604-01-17]

    Отклонения напряжения от номинальных значений происходят из-за суточных, сезонных и технологических изменений электрической нагрузки потребителей; изменения мощности компенсирующих устройств; регулирования напряжения генераторами электростанций и на подстанциях энергосистем; изменения схемы и параметров электрических сетей.

    [В. В. Суднова. Качество электрической энергии]


    Тематики

    EN

    DE

    FR

    Смотри также

    12. Отклонение напряжения

    D. Spannungsabweichung

    E. Voltage deviation

    F. Ecart de tension

    Величина, равная разности между значением напряжения в данной точке системы электроснабжения в рассматриваемый момент времени и его номинальным или базовым значением

    Источник: ГОСТ 23875-88: Качество электрической энергии. Термины и определения оригинал документа

    Франко-русский словарь нормативно-технической терминологии > ecart de tension

  • 12 haute tension

    1. высокое напряжение

    1

     

    высокое напряжение
    -
    [IEV number 151-15-05]

    EN

    high voltage (1)
    high tension (1)
    HV (1), abbreviation
    voltage having a value above a conventionally adopted limit
    NOTE – An example is the set of upper voltage values used in bulk power systems.
    Source: 601-01-27 MOD
    [IEV number 151-15-05]

    FR

    haute tension (1), f
    HT (1), abréviation
    tension électrique de valeur supérieure à une limite adoptée par convention
    NOTE – Un exemple est l'ensemble des tensions les plus élevées utilisées dans les réseaux de production-transport d'énergie électrique.
    Source: 601-01-27 MOD
    [IEV number 151-15-05]

    2

     

    высокое напряжение
    -

    EN

    High Voltage
    HV

    systems with nominal voltage in range above 1 000 V a.c. and up to and including 15 kV a.c.
    NOTE This definition differs from the conventional definition.
    [IEC/PAS 60092-510, ed. 1.0 (2009-04)]

    FR

    -

    Синонимы

    • ВН

    EN

    DE

    FR

    Франко-русский словарь нормативно-технической терминологии > haute tension

  • 13 HT

    1. высокое напряжение

    1

     

    высокое напряжение
    -
    [IEV number 151-15-05]

    EN

    high voltage (1)
    high tension (1)
    HV (1), abbreviation
    voltage having a value above a conventionally adopted limit
    NOTE – An example is the set of upper voltage values used in bulk power systems.
    Source: 601-01-27 MOD
    [IEV number 151-15-05]

    FR

    haute tension (1), f
    HT (1), abréviation
    tension électrique de valeur supérieure à une limite adoptée par convention
    NOTE – Un exemple est l'ensemble des tensions les plus élevées utilisées dans les réseaux de production-transport d'énergie électrique.
    Source: 601-01-27 MOD
    [IEV number 151-15-05]

    2

     

    высокое напряжение
    -

    EN

    High Voltage
    HV

    systems with nominal voltage in range above 1 000 V a.c. and up to and including 15 kV a.c.
    NOTE This definition differs from the conventional definition.
    [IEC/PAS 60092-510, ed. 1.0 (2009-04)]

    FR

    -

    Синонимы

    • ВН

    EN

    DE

    FR

    Франко-русский словарь нормативно-технической терминологии > HT

  • 14 tension nominate

    1. номинальное напряжение пьезоэлектрического (электромеханического) фильтра

     

    номинальное напряжение пьезоэлектрического (электромеханического) фильтра (Uном, Unom)
    Значение входного напряжения, при котором измеряют параметры пьезоэлектрического (электромеханического) фильтра.
    [ ГОСТ 18670-84]

    Тематики

    EN

    FR

    Франко-русский словарь нормативно-технической терминологии > tension nominate

  • 15 tension assignée d'un parafoudre

    1. номинальное напряжение ОПН

     

    номинальное напряжение

    Действующее значение напряжения промышленной частоты, которое ограничитель может выдерживать в течение 10 с в процессе рабочих испытаний. Номинальное напряжение должно быть не менее 1,25 наибольшего длительно допустимого рабочего напряжения.
    [ ГОСТ Р 52725-2007]

    EN

    rated voltage of an arrester
    Ur

    maximum permissible r.m.s. value of power-frequency voltage between its terminals at which it is designed to operate correctly under temporary overvoltage conditions as established in the operating duty tests
    NOTE 1 The rated voltage is used as a reference parameter for the specification of operating characteristics.
    NOTE 2 The rated voltage as defined in this standard is the 10 s power-frequency voltage used in the operating duty test after high-current or long-duration impulses. Tests used to establish the voltage rating in IEC 60099-1, as well as some national standards, involve the application of repetitive impulses at nominal current with power-frequency voltage applied. Attention is drawn to the fact that these two methods used to established rating do not necessarily produce equivalent values (a resolution to this discrepancy is under consideration).
    [IEC 60099-4, ed. 2.0 (2004-05)]

    FR

    tension assignée d'un parafoudre
    Ur

    valeur maximale de la tension efficace à fréquence industrielle admissible entre ses bornes pour laquelle le parafoudre est prévu pour fonctionner correctement dans des conditions de surtension temporaires comme il est défini dans les essais de fonctionnement
    NOTE 1 La tension assignée est utilisée comme paramètre de référence pour la spécification des caractéristiques de fonctionnement.
    NOTE 2 La tension assignée comme définie dans la présente norme est la tension à fréquence industrielle de 10 s, utilisée pour vérifier la stabilité après application des chocs de courant de grande amplitude ou de longue durée lors de l'essai de fonctionnement. Les essais utilisés pour définir la tension assignée dans la CEI 60099-1, ainsi que dans certaines normes nationales, impliquent l'application de chocs répétés au courant nominal pendant que la tension à fréquence industrielle est appliquée. On attire l'attention sur le fait que ces deux méthodes utilisées pour définir les valeurs assignées ne produisent pas nécessairement des valeurs équivalentes (une résolution de cette différence est à l'étude).
    [IEC 60099-4, ed. 2.0 (2004-05)]

    Тематики

    • высоковольтный аппарат, оборудование...

    EN

    FR

    Франко-русский словарь нормативно-технической терминологии > tension assignée d'un parafoudre

  • 16 courant de référence d'un parafoudre

    1. классификационный ток ОПН

     

    классификационный ток ОПН
    Iкл

    Амплитудное значение (более высокое амплитудное значение из двух полярностей, если ток асимметричен) активной составляющей тока промышленной частоты, которое используется для определения классификационного напряжения ОПН и нормируется изготовителем.
    [ ГОСТ Р 52725-2007]

    EN

    reference current of an arrester
    peak value (the higher peak value of the two polarities if the current is asymmetrical) of the resistive component of a power-frequency current used to determine the reference voltage of the arrester
    NOTE 1 The reference current will be high enough to make the effects of stray capacitances at the measured reference voltage of the arrester units (with designed grading system) negligible and is to be specified by the manufacturer.
    NOTE 2 Depending on the nominal discharge current and/or line discharge class of the arrester, the reference current will be typically in the range of 0,05 mA to 1,0 mA per square centimetre of disc area for single column arresters.
    [IEC 60099-4, ed. 2.0 (2004-05)]

    FR

    courant de référence d'un parafoudre
    valeur de crête (la plus grande des deux polarités si le courant est dissymétrique) de la composante résistive du courant à fréquence industrielle utilisée pour déterminer la tension de référence d'un parafoudre.
    NOTE 1 Il convient que le courant de référence soit suffisamment élevé pour rendre négligeables les effets des capacités parasites aux tensions de référence mesurées sur les éléments de parafoudre (avec leur système de répartition) et qu’il soit spécifié par le constructeur.
    NOTE 2 Fonction du courant de décharge nominal et/ou de la classe de décharge de ligne du parafoudre, il convient que le courant de référence soit typiquement dans la gamme de 0,05 mA à 1,0 mA par centimètre carré de surface de disque pour les parafoudres à colonne unique
    [IEC 60099-4, ed. 2.0 (2004-05)]

    Тематики

    • высоковольтный аппарат, оборудование...

    EN

    FR

    Франко-русский словарь нормативно-технической терминологии > courant de référence d'un parafoudre

  • 17 catégorie de surtension (d'un circuit ou dans un réseau)

    1. категория перенапряжения (в цепи или электрической системе)

     

    категория перенапряжения (в цепи или электрической системе)
    Условное число, основанное на ограничении (или регулировании) значений ожидаемого переходного перенапряжения, возникающего в цепи (или в электрической системе с различными номинальными напряжениями), зависящее от способов воздействия на перенапряжения.
    Примечание. В электрической системе переход от одной категории перенапряжения к другой, более низкой, достигается средствами, совместимыми с требованиями к переходным участкам, например с помощью устройства для защиты от перенапряжений или последовательно-параллельного присоединения импеданса, способного рассеять, поглотить или отклонить энергию соответствующего импульсного тока с целью снижения переходного перенапряжения до желательно меньшей категории перенапряжения.
    [ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]

    категория перенапряжения
    Категория электротехнического оборудования по стойкости изоляции к импульсным перенапряжениям (всего четыре категории: I, II, III, IV)
    [Интент]

    EN

    overvoltage category (of a circuit or within an electrical system)
    conventional number based on limiting (or controlling) the values of prospective transient overvoltages occurring in a circuit (or within an electrical system having different nominal voltages) and depending upon the means employed to influence the overvoltages
    NOTE In an electrical system, the transition from one overvoltage category to another of lower category is obtained through appropriate means complying with interface requirements, such as an overvoltage protective device or a series-shunt impedance arrangement capable of dissipating, absorbing, or diverting the energy in the associated surge current, to lower the transient overvoltage value to that of the desired lower overvoltage category
    [IEC 60947-1, ed. 5.0 (2007-06)]

    FR

    catégorie de surtension (d'un circuit ou dans un réseau)
    nombre conventionnel, basé sur la limitation (ou la commande) des valeurs des surtensions transitoires présumées apparaissant dans un circuit (ou dans un réseau où existent des sections de tensions nominales différentes) et dépendant des moyens employés pour agir sur ces surtensions
    NOTE Dans un réseau, le passage d'une catégorie de surtension à une autre de catégorie inférieure est réalisé à l'aide de moyens appropriés répondant aux prescriptions d'interface, tels qu'un dispositif de protection contre les surtensions ou des impédances disposées en séries et/ou en parallèle capables de dissiper, d'absorber ou de détourner l'énergie du courant de surcharge correspondant, afin d'abaisser la valeur des surtensions transitoires à celle qui correspond à la catégorie de surtension inférieure recherchée
    [IEC 60947-1, ed. 5.0 (2007-06)]

    Требуемая стойкость к импульсным напряжениям, кВ:

    [ ГОСТ Р 50571-4-44-2011( МЭК 60364-4-44: 2007) ]

    Тематики

    • электротехника, основные понятия

    EN

    FR

    Франко-русский словарь нормативно-технической терминологии > catégorie de surtension (d'un circuit ou dans un réseau)

См. также в других словарях:

  • nominal voltage — vardinė įtampa statusas T sritis automatika atitikmenys: angl. nominal voltage; rated voltage; voltage rating vok. Nennspannung, f rus. номинальное напряжение, n pranc. tension assignée, f; tension de régime, f; tension nominale, f ryšiai:… …   Automatikos terminų žodynas

  • nominal voltage — vardinė įtampa statusas T sritis fizika atitikmenys: angl. nominal voltage; rated voltage vok. Nennspannung, f rus. номинальное напряжение, n pranc. tension assignée, f; tension nominale, f …   Fizikos terminų žodynas

  • nominal voltage — See rated voltage …   Dictionary of automotive terms

  • Voltage regulator — A popular three pin 12 V DC voltage regulator IC. A voltage regulator is an electrical regulator designed to automatically maintain a constant voltage level. A voltage regulator may be a simple feed forward design or may include negative feedback …   Wikipedia

  • Voltage doubler — A voltage doubler is an electronic circuit which charges capacitors from the input voltage and switches these charges in such a way that, in the ideal case, exactly twice the voltage is produced at the output as at its input. The simplest of… …   Wikipedia

  • voltage — [1] A difference in electrical potential between one end of a circuit and the other. Also called electromotive force (EMF). Voltage causes current to flow. Measured in volts. [2] Term used to indicate the electrical potential or electromotive… …   Dictionary of automotive terms

  • voltage rating — vardinė įtampa statusas T sritis automatika atitikmenys: angl. nominal voltage; rated voltage; voltage rating vok. Nennspannung, f rus. номинальное напряжение, n pranc. tension assignée, f; tension de régime, f; tension nominale, f ryšiai:… …   Automatikos terminų žodynas

  • nominal — 1. adjective /ˈnɒm.ɪnl̩/ a) Of, resembling, relating to, or consisting of a name or names. He gave me only a nominal sum for my services. b) Assigned to or bearing a persons name. The nominal voltage is 1.5 V, but the actual figure is usually… …   Wiktionary

  • Nominal impedance — in electrical engineering and audio engineering refers to the approximate designed impedance of an electrical circuit or device. The term is applied in a number of different fields, most often being encountered in respect of: The nominal value of …   Wikipedia

  • Nominal watt — Nominal wattage is used to simplify the measurement of the efficiency of a loudspeaker. The impedance of a loudspeaker varies with frequency. This means that if different sine wave tones are fed into the loudspeaker at the same voltage (or the… …   Wikipedia

  • Voltage Identification Digital — or VID is a circuit concept developed to provide the central processing unit (CPU) of a computer with the appropriate supply voltage. Instead of having a power supply unit generate some fixed voltage, the CPU uses a small set of digital signals,… …   Wikipedia

Поделиться ссылкой на выделенное

Прямая ссылка:
Нажмите правой клавишей мыши и выберите «Копировать ссылку»